Відео

Imagine him playing poker facd with lady gaga

A note for those who open one of these up to repair in the future. I found that on my RD700sx it was not obvious how to re-install the sensor boards at the correct angle. In my case, the previous owner had been in it before and placed the boards at a slightly different angle than they were suppose to be, resulting in a large number of keys barely working or not at all. While the boards will appear to fit nicely if you have them in the shallower angle, it will result in few keys working properly. Be sure to install the boards at the same angle as the plastic mounting tabs are cut (where the screws are installed). If you can look in from the side and see a gap near the bottom of where the mounting tab gets screwed on, then you've got the board too shallow. Tip is slightly steeper until it clicks into the little plastic holding teeth on the bottom rather than resting way out on the outer edges of the teeth. Difficult to explain without photos, but If you take one of these apart, it should become more obvious. Many parts, including the sensor strips, hammers, keys, pads, and more are still available (in 2024) from the Syntaur website from what I could glean on a google search. Hope this helps someone down the road.

So if I get a gallon of auto paint I can do this with a foam roller?

he actually taped it up bruh coulda sprayed it

Looks good

Bedliner paint would be great 😅

Looking good 👍

Who cares if it lasts a month… police were looking for a red one 😂

And now change the paperwork. This is not a dark green car anymore.

What kind of paint did you use? Considering this.

Used to do this on the old horse box. Worked a treat. 😊

Looking Good 😳

It ain't stupid if it works

The only issue is this doesn’t look like automotive paint, which means it won’t have the necessary hardeners and other chemicals needed to bond to metal and primer.

Looks fine to me

I’ve seen this method after wet sanding and it’s honestly not bad.

Had an aunt painted her yugo pink like that back in 94

not too bad

Old man that lived down the street from me growing up did the same thing. You could only tell up close. He didn't have foam rollers, and it turned out great. Looks nice to me, great work man.

That's one way to prevent any overspray

I like it 💪

The only way is to just break apart the item. Unless they fix this issue.

For me it was a weak spark due to the spark plug wires/ ignition coil. I successfully modified a GM D555/576 coil to work for my bike. Just used a couple shaved down spade connectors and a spark plug wiring kit. I had to make have moto and half car spark plug wires by salvaging my old moto spark boots and the other half from the wiring kit. Then it will fit the GM coil. Good luck 👍

Im looking to buy one of these would you be interested in selling or at least where would be a good place to find one

Thanks for the video. Such good information explained in a clear and handsome manner.

ok idk if yall can help me ik its not reddit but my mic just sounds like super distant and i cant fix it

GREAT BAND

I bought this software based on this video online and the official link of this software won't even show in my email or anything. Please guys do not buy this software they will take your money and won't help you at all😢. They just took my money and I don't have no software link or anything?

Hi! I’m still having the issue :/ what is a good email for you?

I'll release a song for this video next week. Almost complete.

My first motorcycle as a kid

Where would you line up the mark: 1). T at the crankshaft, and T at the cam sprocket. 2) T at the crankshaft, and F at the cam sprocket. 3). T at the crankshaft, and between T&F at the sprocket? I did option 1 above, it did not fire. Then I did option 2 above, it fires and drive ok, but when I engage the PTO clutch, it stalled. It seems the engine is not running at its ultimate state. I would like to try option 3 above and see if it solves the PTO clutch engaging issue. Is there anyone that have had this issue before and can help me? Thanks

The brake is on

wtf is this cr4p? lame as f**k

Esse Steve Moore é o jogador de ......... de ..............Ice Hockey? Este Steve Moore é muito bom no que faz, me encanta.

Nice example of an old XR80. Sounds tight.

Now put some gas in the tank to see if the carburetor works.

The real Briggs & Stratton engines, first or second pull on starting. Not the new junk coming from China they won’t even half as long as these older originals.

that starting fluid is some good stuff.

This kid's awesome...good job!

Awesome! Owned our Midnight Special RX50 since it was new! Still ride!

I enjoyed it a lot.

I love this drummer, he's not only very funny but extremely talented.

wasting my time watching this....

THE AMERICAN HELICOPTER MUSEUM IVE BEEN THERE BEFORE

At minute 11:43 Uncle Charlie reads a Letter to Dad written by my daughter, Leslie Suzanne Butler at age 10. My other daughter found this while searching for some Children's Bible Hour recordings to let her daughter hear...thank you so much for having this recording...The Children's Bible Hour was a great influence on both my girls for many years!❤❤❤

Thank you so much for this! It saved my bacon. The only thing I would add is about the ribbon cables. I wasn't sure if there was a release for them or not so I hummed and hawed until eventually I just wiggled them out carefully. Also to stress that you need to detach the two ribbons attached to the keyboard and not to the circuitry which isn't clear at first. Also my ribbons were taped down so you need to remove the adhesive a little in order to attach/reattach them. Other than that it worked like a dream and saved me a lot of hassle and money. Thanks again!

would u sell it

6 hrs to get here

Thank you 😭🤝❤️